Power over Ethernet has a range of about 100 meters
from the network switch. Should PoE be needed at
distances greater than 100 meters, solutions might
include electrical rewiring for AC power at a remote
location or moving network communications closets,
both require extensive labor and are costly and time
consuming. Phihong has developed a more cost
effective option with the POE16S-1AFG. Users can now
double the effective PoE Range of their devices to 200
meters while saving time and money.
By using your standard Category 5 or better Ethernet
cables the POE16S-1AFG takes its power from an
IEEE802.3at PoE Plus device (33.6W). The output
power is then dropped to be IEEE802.3af compatible
19W.
Its design is intended for use when expanding existing
networks. In the image seen above, the user wanted
to add an additional security camera 200 meters
from the network switch. The fi rst Ethernet cable not
exceeding 100 meters should be laid from the switch to
the POE16S-1AFG with a PoE Plus or better midspan
in between; another cable not exceeding 100 meters
should run from the extender to the security camera.
The POE16S-1AFG is designed to be plug-and-
play, therefore is no additional software or hardware
installation required. Upon powering up, the device will
work automatically by taking the necessary power from
the midspan and relaying it on to the PoE device.
Compatible IEEE802.3af devices include but are not
limited to Security Cameras, Sensors, and wireless
network and access controllers.
Installation Sequence:
1) Using the appropriate Ethernet cable, connect the
PoE In to the midspan inside the communications
cabinet.
2) Using an appropriate Ethernet cable, connect the
PoE Out to the given device, i.e. security camera
3) Wait a few seconds to allow connectivity before
reading the LED indicators.
PoE IN
Green LED 1: 10Mb activity
Green LED 2: 100Mb activity
Green LED 3: Gigabit activity
PoE OUT
Green LED 1: 10Mb activity
Green LED 2: 100Mb activity
Green LED 3: Gigabit activity
Ethernet
Green LED 1: Input power “ON”
Red LED: Fault detected
Green LED 2: Valid IEEE802.3af
load detected and connected
Should any connection fault occur the LEDs will blink
a code diagnosing the problem, for a complete listing
of those fault codes, please see the listing below under
troubleshooting. They are also listed on the data sheet
for this product on the individual product page on the
website, www.phihong.com.
Input Power
IEEE802.3at PoE Plus (30W) and
IEEE802.3af compatible (19W)*.
Input must be PoE.
Output Power
IEEE802.3af compliant 9W
Ethernet
Category 5 or better
Dimensions
120x60x32mm
(4.72x2.36x1.26in)
Weight
0.5kg
(1.1lb)
Operating
Temperature
0 to +55°C
32 to +131°F
Humidity
5 - 90%
*If IEEE802.3af is the input power source then the output
power is restricted to approximately 8W.
47800 Fremont Blvd.
Fremont, CA 94538, USA
Tel: 1-510-445-0100
Fax: 1-510-445-1678
Email: Poe@phihongusa.com
ADVANCING
POE TECHNOLOGY
Whatsapp
Mail
Facebook
Kell segítség?
Kérdések száma: 0
Van kérdése a (z) Phihong POE16S-1AFG kapcsán, vagy segítségre van szüksége? Tegye fel a kérdését itt. Adjon világos és átfogó leírást a problémáról és a kérdéséről. Minél részletesebben ábrázolja a problémát és a kérdést, annál könnyebben tudnak más Phihong POE16S-1AFG tulajdonosok megfelelő választ adni a kérdésére.
Kapcsolódó Phihong POE16S-1AFG
Itt ingyenesen megtekintheti a (z) Phihong POE16S-1AFG kézikönyvét. Ez a kézikönyv a Wifi ismétlők kategóriába tartozik, és 1 ember értékelte, átlagosan 8.8. Ez a kézikönyv a következő nyelveken érhető el: Engels. Van kérdése a (z) Phihong POE16S-1AFG kapcsán, vagy segítségre van szüksége? Itt tedd fel kérdéseidet
POE16S-1AFG User ManualPower over Ethernet and Data ExtenderPower over Ethernet has a range of about 100 metersfrom the network switch. Should PoE be needed atdistances greater than 100 meters, solutions mightinclude electrical rewiring for AC power at a remotelocation or moving network communications closets,both require extensive labor and are costly and timeconsuming. Phihong has developed a more costeffective option with the POE16S-1AFG. Users can nowdouble the effective PoE Range of their devices to 200meters while saving time and money.By using your standard Category 5 or better Ethernetcables the POE16S-1AFG takes its power from anIEEE802.3at PoE Plus device (33.6W). The outputpower is then dropped to be IEEE802.3af compatible19W.Its design is intended for use when expanding existingnetworks. In the image seen above, the user wantedto add an additional security camera 200 metersfrom the network switch. The fi rst Ethernet cable notexceeding 100 meters should be laid from the switch tothe POE16S-1AFG with a PoE Plus or better midspanin between; another cable not exceeding 100 metersshould run from the extender to the security camera.The POE16S-1AFG is designed to be plug-and-play, therefore is no additional software or hardwareinstallation required. Upon powering up, the device willwork automatically by taking the necessary power fromthe midspan and relaying it on to the PoE device.Compatible IEEE802.3af devices include but are notlimited to Security Cameras, Sensors, and wirelessnetwork and access controllers.Installation Sequence:1) Using the appropriate Ethernet cable, connect thePoE In to the midspan inside the communicationscabinet.2) Using an appropriate Ethernet cable, connect thePoE Out to the given device, i.e. security camera3) Wait a few seconds to allow connectivity beforereading the LED indicators.PoE INGreen LED 1: 10Mb activityGreen LED 2: 100Mb activityGreen LED 3: Gigabit activityPoE OUTGreen LED 1: 10Mb activityGreen LED 2: 100Mb activityGreen LED 3: Gigabit activityEthernetGreen LED 1: Input power “ON”Red LED: Fault detectedGreen LED 2: Valid IEEE802.3afload detected and connectedShould any connection fault occur the LEDs will blinka code diagnosing the problem, for a complete listingof those fault codes, please see the listing below undertroubleshooting. They are also listed on the data sheetfor this product on the individual product page on thewebsite, www.phihong.com.Input PowerIEEE802.3at PoE Plus (30W) andIEEE802.3af compatible (19W)*.Input must be PoE.Output PowerIEEE802.3af compliant 9WEthernetCategory 5 or betterDimensions120x60x32mm(4.72x2.36x1.26in)Weight0.5kg(1.1lb)OperatingTemperature0 to +55°C32 to +131°FHumidity5 - 90%*If IEEE802.3af is the input power source then the outputpower is restricted to approximately 8W.47800 Fremont Blvd.Fremont, CA 94538, USATel: 1-510-445-0100Fax: 1-510-445-1678Email: Poe@phihongusa.comADVANCINGPOE TECHNOLOGY
