Intel S5520SC

Intel S5520SC kézikönyv

(1)
  • Intel is a registered trademark of Intel Corporation or its
    subsidiaries in the United States and other countries.
    *Other names and brands may be claimed as the property
    of others. Copyright © 2011, Intel Corporation. All rights
    reserved.
    Warning
    Read all caution and safety
    statements in this document
    before performing any of the
    instructions. Also see the Intel
    ®
    Server Board and Server Chassis
    Safety Information document at:
    http://support.intel.com/support/
    motherboards/server/sb/cs-010770
    .htm for complete safety information.
    Warning
    Installation and service of
    this product should only be
    performed by qualified service
    personnel to avoid risk of injury from
    electrical shock or energy hazard.
    Tools Required
    Caution
    Observe normal ESD
    [Electrostatic Discharge]
    procedures during system
    integration to avoid possible
    damage to server board and/or
    other components.
    Anti-static
    wrist strap
    #2 Phillips*
    screwdriver
    E39546-009
    Intel® Workstation Board S5520SC
    Quick Start User's Guide
    For details on these chassis or to select a third-party
    chassis, please visit:
    http://support.intel.com/support/motherboards/server.
    When installing the server board into a reference chassis,
    refer to the reference chassis instructions.
    Service Guides are also available on the CDs that accompanied
    your Intel® Workstation Board S5520SC.
    If you are not familiar with ESD (Electrostatic Discharge) procedures
    used during system integration, please see the Intel® Workstation Board S5520SC
    Service Guide, available on the Intel® Server Deployment Toolkit 3.0 CD or at
    http://support.intel.com/support/motherboards/server/S5520SC/manual.htm
    Thank you for buying the Intel® Workstation Board
    S5520SC. The following information will help you
    integrate your new server board into a server
    chassis. The Intel® Workstation Board S5520SC
    is designed for use with the Intel® Server
    Chassis SC5600Base and the Intel® Server
    Chassis SC5650WS.
    5a
    1
    Preparing
    the Chassis
    Observe normal ESD
    (Electrostatic Discharge)
    procedures.
    Place your
    Intel
    ®
    Server
    Chassis on a flat anti-static
    surface to perform the
    following integration
    procedures. Observe ESD
    procedures before
    reaching inside to make
    server board connections
    or install components.
    2
    Installing the I/O Shield and Attach I/O Labels
    Install the I/O
    shield
    Attach the Labels to the I/O Shield
    Shield installs from inside
    of chassis. The labels
    should be visible from the
    outside of the chassis.
    Prepare the I/O shield
    Do not remove the three circular
    knockouts that are at the edge next to
    the openings for the NIC, USB, Serial A,
    and 1394 ports. Use caution so you do
    not deform the shield.
    Insert one side edge of
    shield as shown.
    Push shield firmly into
    chassis opening until
    it clicks into place.
    B
    A
    Remove the backing from the I/O
    shield labels included with your
    server board.
    Press each label onto the I/O
    shield as shown.
    B
    A
    Chassis Back
    Panel Opening
    Intel
    ®
    Server Chassis
    SC5650WS shown
    Note: Make sure you install the labels
    on the correct side of the I/O shield.
    Note the orientation of the cutouts in
    the drawing before attaching your labels.
    NIC 1
    USB 2
    USB 3
    NIC 2
    USB 0
    USB 1
    MSB
    Diagnostic LEDs
    LSB
    ID
    Serial A
    1394
    Line In
    MIC In
    Labels on outside
    face of I/O shield
    B
    A
    3
    Install Workstation
    Board Bumpers
    Prepare Workstation Board
    Rotate board to show underside and hold upright
    as shown.
    Locate the five circles as shown.
    B
    A
    Attach the Bumpers
    Remove the backing from each bumper.
    Press a bumper onto each of the five circles.
    D
    C
    NOTE:
    If you are using an Intel
    ®
    Server Chassis you must install the chassis
    bumpers included with the chassis. Refer to your Intel
    ®
    Workstation Board
    and Intel
    ®
    Server Chassis Quick-Start User’s Guide for proper bumper
    installation guidelines. If you are using a non-Intel server chassis that
    includes bumpers, refer to the non-Intel server chassis documentation for
    the correct bumper installation procedure. If the non-Intel server chassis
    does not include bumpers, then you should consult with the chassis vendor
    to determine whether bumpers are required or not.
    B
    D
    C
    CAUTION: To avoid damage to the board,
    do not lay flat with the component side down.
    4
    Install the Workstation Board
    B. Attach the Workstation Board
    A. Insert Workstation Board
    Place the board into the chassis, making
    sure that back panel I/O openings and
    chassis standoffs align correctly.
    The Intel
    ®
    Server Chassis SC5600Base and the Intel
    ®
    Server Chassis SC5650WS use different screws
    to attach the workstation board to the chassis. Use the screws indicated for your chassis.
    For a non-Intel server chassis, use the fasteners that came with your chassis.
    When using the Intel
    ®
    Server Chassis
    SC5600Base, remove the rear chassis fan
    and then insert the I/O connector
    side (back) of the board first.
    IMPORTANT NOTE:
    If you are using a
    non-Intel server chassis, see your
    chassis documentation for preparatory
    steps prior to server board installation.
    Intel
    ®
    Server Chassis
    SC5600Base Shown
    Intel
    ®
    Server Chassis
    SC5650WS Shown
    I/O Openings
    Front
    Edge of
    Board
    Intel
    ®
    Server
    Chassis
    SC5650WS
    Intel
    ®
    Server
    Chassis
    SC5600Base
    Intel
    ®
    Server Chassis SC5600Base: Attach the
    board to the chassis at the nine locations indicated
    by the solid blue arrows in the figure [ ] and at
    the one location indicated by the solid red arrow [ ].
    Intel
    ®
    Server Chassis SC5650WS: Push down
    firmly to engage the snap-top standoffs at the
    location indicated by the solid red arrow [ ].
    Use screws to attach the board to the chassis at
    the nine locations indicated by the solid blue
    arrows [ ].
    When using the Intel
    ®
    Server Chassis SC5650WS,
    remove the front drive bay
    and rear chassis fan, and then
    insert the front of the board first.
    Slide the board back so the I/O
    connectors fit through the I/O shield.
    CPU 1 Socket
    CPU 2 Socket
    5b
    Minimum Hardware Requirements
    To avoid integration difficulties and possible board damage,
    your system must meet the following minimum requirements:
    Processor:
    Minimum of one Intel
    ®
    Xeon
    ®
    Processor 5500 Series
    or one Intel Xeon Processor 5600 Series.
    Supports maximum 95 watt processor in the Intel
    ®
    Server
    Chassis SC5600Base.
    Supports maximum 130 watt processor in the Intel
    ®
    Server
    Chassis SC5650WS.
    Memory Type:
    Minimum of one 1 GB, 240-pin,
    RDIMM or UDIMM, DDR3-800, DDR3-1066, or DDR3-1333.
    AC Power: SSI EPS 12V compliant power supply.
    Recommended
    minimum of 670 Watts with 3 A of standby
    current, or calculate your system power demand with the power
    budget tool.
    Heat Sink(s):
    Minimum of one active heat sink for the Intel
    ®
    Server Chassis SC5600Base and SC5650WS.
    For a complete list of compatible processors, heat sinks, and memory, see:
    http://support.intel.com/support/motherboards/server/s5520SC/
    NOTE: Graphics cards with power greater than 75 W must be self-cooled
    with exhaust out the back of the chassis.
    CAUTION:
    Supported
    Processor
    Supported
    Graphics Card
    Maximum 95
    watt processor
    One maximum
    150 watt graphics
    card in PCI
    Express* Slot 6
    Maximum 130 watt processor
    In the Intel
    ®
    Server Chassis
    SC5600Base
    In the Intel
    ®
    Server Chassis
    SC5650WS
    ONE maximum 300 watt graphics card in
    PCI Express* Slot 6 or TWO maximum
    150 watt graphics cards. Empty PCI
    Express* Slot 3 when a graphics card is
    installed in PCI Express* slot 4.
    6
    CPU 1 Socket
    CPU 2 Socket
    A
    Attach auxiliary power signal
    connector to the workstation board.
    B
    C
    Attach the CPU 1 power connector
    to the workstation board.
    Attach the CPU 2 power connector
    to the workstation board.
    IMPORTANT NOTE:
    If you are using a non-Intel
    server chassis with an ATX power supply, see
    the documentation that came with your chassis
    for installation information.
    D
    Attach the main power connector to
    the workstation board.
    Latch
    Tab
    Main Power
    Connector Detail
    CPU Power
    Connector Detail
    Auxiliary Signal
    Power Detail
    CAUTION:
    Note the location of the latch on each
    power cable connector and align it with the
    matching tab on each workstation board socket.
    A
    B
    C
    D
    Go to Side 2
    Make Workstation Board Power Connections
    Install the Processor(s)
    A. Open the Socket Lever
    Push the lever handle down
    and away from the socket to
    release it.
    Rotate the lever open all
    the way.
    B. Open the Load Plate
    Push the rear tab with your
    finger tip to bring the front
    end of the load plate
    up slightly.
    Open the load plate as shown.
    A
    B
    A
    B
    C. Remove the
    Processor
    Protective Cover
    Take the processor out
    of the box and remove
    the protective shipping
    cover.
    A
    A
    Cautions:
    2. When unpacking a processor, hold by the
    edges only to avoid touching the gold
    contact wires.
    1. When opening a socket, DO NOT TOUCH
    the gold socket wires.
    A
    B
    A
    B
    Install the Processor(s) ... continued
    E. Close Load Plate and Socket Lever
    Close the
    load plate
    all the
    way as
    shown.
    Remove the protective cover after it been
    automatically disengaged from the load plate.
    Close the socket lever.
    C
    A
    B
    CAUTION: The underside
    of the processor has
    components that may damage
    the socket wires if installed
    improperly.
    Processor must align
    correctly with the
    socket opening
    before installation.
    DO NOT DROP processor
    into the socket!
    A
    Components
    Orient the processor with the socket
    so that the orientation notches on
    the processor align with the two
    orientation posts on the socket.
    A
    Install the processor as shown.
    Orientation Posts
    Orientation Notches
    A
    Install the ProcessorD.
    B
    C
Intel S5520SC

Kell segítség?

Kérdések száma: 0

Van kérdése a (z) Intel S5520SC kapcsán, vagy segítségre van szüksége? Tegye fel a kérdését itt. Adjon világos és átfogó leírást a problémáról és a kérdéséről. Minél részletesebben ábrázolja a problémát és a kérdést, annál könnyebben tudnak más Intel S5520SC tulajdonosok megfelelő választ adni a kérdésére.

Itt ingyenesen megtekintheti a (z) Intel S5520SC kézikönyvét. Ez a kézikönyv a Alaplapok kategóriába tartozik, és 1 ember értékelte, átlagosan 7.7. Ez a kézikönyv a következő nyelveken érhető el: Angol. Van kérdése a (z) Intel S5520SC kapcsán, vagy segítségre van szüksége? Itt tedd fel kérdéseidet

Intel S5520SC specifikációk

Általános
Márka Intel
Modell S5520SC
Termék Alaplap
EAN 675900990548, 6759009905482, 735858207522, 735858213806
Nyelv Angol
Fájltípus PDF
Hátlapi ki-/bemeneti csatlakozók
PS/2 portok száma 0
Soros portok száma 2
Firewire (IEEE 1394) portok 1
SAS csatlakozók száma 0
Ethernet LAN (RJ-45) portok 2
Bővítő helyek
PCI-expressz x16 csatlakozók 2
PCI-expressz x4 csatlakozók 1
PCI csatlakozók 1
PCI Express x4 (Gen 1.x) bővítőhelyek 1
PCI Express x8 (Gen 1.x) bővítőhelyek 1
PCI-expressz x16 (Gen 2.x) bővítőhelyek 2
PCI Express x16 (Gen 3.x) bővítőhelyek 0
Memória
ECC Igen
Maximális RDIMM memória 192 GB
Memória-sávszélesség (max.) 64 GB/s
Támogatott memóriatípusok DDR3-SDRAM
Támogatott memória órajelsebességi fokozatok 800,1066,1333 Mhz
Maximális belső memória 192.38 GB
További jellemzők
Maximális UDIMM memória 192 GB
Gépház típusa Tower
A rendelkezésre álló beágyazott opciók Igen
CPU konfiguráció (max.) 2
PCI Express x8 (Gen 2.x) bővítőhelyek 0
PCI Express x8 (Gen 3.x) bővítőhelyek 0
Thermal Design Power (TDP) 130 W
Alaplap ARK ID 36600
Exportellenőrzési árucikkszám (ECCN) 5A992C
Termékbesoroló automatizált nyomkövető rendszer (CCATS) G135162
Intel Node Manager Igen
DIMM-foglalatok száma 12
A támogatott processzorok száma 2
Tárolásvezérlők
RAID-szintek 0,1
Támogatott tárolóeszköz-meghajtó csatlakozási felületek SATA
Processzor
Intel® Xeon sorozat E5500,E5600,L5500,L5600,W5500,X5500,X5600
QPI sebesség 4.8,5.86,6.4 GT/másodperc
A támogatott magokhoz tartozó processzorok száma 2,4,6
Litográfia 45 nm
Processzor hőteljesítménye (max.) 130 W
A PCI Expressz sávok maximális száma 5
A processzor által támogatott ECC Igen
A processzor által támogatott memória sávszélesség (max.) 64 GB/s
Termékcsalád Öröklött szerver / munkaállomás alaplap
Terméksorozat Intel S5520SC
Termék kódneve Shady Cove
A processzor által támogatott maximális belső memória 192 GB
Processzor gyártója Intel
Processzor-foglalat LGA 1366 (Socket B)
Hálózat
Ethernet/LAN csatlakozás Igen
Ethernet csatlakozó típusa Fast Ethernet,Gigabit Ethernet
Wi-Fi Nincs
Jellemzők
Járulékos komponens Munkaállomás
Audió kimeneti csatornák 7.1 csatornák
Piaci szegmens Szerver
Harmonized System (HS)-kód 8473301180
Alaplap kialakítása SSI EEB
Alaplapi chipkészlet Intel® 5520
Speciális processzor funkciók
Intelligens platformkezelő kezelőfelület (IPMI) támogatás Igen
Megbízott platform modul (TPM) Igen
Intel® Intelligent Power Node Manager Igen
Rendelkezésre álló integrált rendszerek Igen
Trusted Platform Module (TPM) verzió 1.2
Intel® Server Management Software Igen
Intel® Remote Management Module Support AXXRMM3
Integrált BMC IPMI-vel Igen
Belső ki-/bemeneti csatlakozók
SATA-csatlakozók száma 6
Integrált SAS portok 0
Az összes SATA csatlakozó száma 6
Grafika
Beépített grafikus adapter Igen
Műszaki adatok
Indítás dátuma Q1'09
PCI támogatás 32 bit/ 33 MHz
Termék típusa Server/Workstation Board
Státusz Discontinued
USB-csatlakozók száma 10
USB verziója 2.0
Maximális memória 192.38 GB
Támogatott RAID konfiguráció Intel Emb RAID (0,1) with upgrd opt to RAID5
Utolsó módosítás 63903513
További URL-információ http://www.intel.com/content/www/us/en/motherboards/server-motherboards/server-board-s5520sc.html
Technikai támogatás záródátumának bejelentése Friday, January 1, 2010
Várható megszakítás időpontja Q2'13
Utolsó rendelés dátuma Monday, March 1, 2010
Utolsó fogadott adatok dátuma Thursday, April 15, 2010
Külső megjelenés SSI EEB (12" x 13")
Tömeg és méretek
Szélesség 304.8 mm
Mélység 330.2 mm