Boss MGR350B

Boss MGR350B kézikönyv

(1)
  • Make the mounting hole size as follows
    3.00” / 76mm
    1
    2
    Snap off break-away tabs to best fit
    your applications depth
    Slip the unit through the hole cutout and into U-bracket
    4
    Install studs mounts into rear of chassis
    5
    3
    Adjust M4 nuts for the best mounting depth
    Firmly tighten remaining M4 nuts
    6
    Secure and waterproof the wiring
    BLUETOOTH
    ®
    ENABLED
    GAUGE HOLE RADIO
    MGR350B
    USER MANUAL
    FEATURING ZERO
    STANDBY CURRENT DRAIN
    QUICK INSTALLATION GUIDE
    MGR350B
    USER MANUAL
    QUICK INSTALLATION GUIDE
    BLUETOOTH
    ®
    GAUGE HOLE RADIO
    PRINTED IN CHINAVER:1.0 EN0215
    BOSS Audio Systems
    3451 Lunar Court • Oxnard, CA 93030
    www.bossaudio.com | 1.805.751.4853
    Tech Support: www.bossaudio.com/support
    The Bluetooth® word mark and logos are registered trademarks
    owned by Bluetooth SIG, Inc. and any use of such marks is under
    license. Other trademarks and trade names are those of their
    respective owners.
    BEFORE YOU START
    IMPORTANT SAFETY PRECAUTIONS
    BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
    Do not turn up the volume so high that you can’t hear what’s
    around you.
    Use caution or temporarily discontinue use in potentially
    hazardous situations.
    Do not operate mobile video equipment while driving a motorized
    vehicle – safe driving and safety consideration of others should
    always be your highest priority.
    Set your volume control at a low setting, then slowly increase the
    sound until you can hear it comfortably without distortion, or ear
    discomfort.
    In the event you should notice smoke, strange noises or odor from
    this product, or any other abnormal signs, immediately turn off the
    power and consult your dealer or the nearest authorized
    BOSS AUDIO Service Center Using this product in this condition
    may result in permanent damage to the system.
    WIRE DIAGRAM
    Thank you for purchasing this
    MGR350B Bluetooth Gauge Hole Radio
    Please read thorough these instructions
    carefully so you will know how to operate
    your model properly.
    After you have nished reading the instructions,
    keep this document in a safe place
    for future reference.
    SUGGESTED MOUNTING METHODS
    INFORMATION TO THE USER
    TROUBLE SHOOTING GUIDE
    !! WARNING !!
    ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY
    RESULT IN HAZARDOUS RADIATION EXPOSURE.
    MGR350B
    (1pc)
    Hexagon Mounting Studs
    (2pcs)
    M4 Secure Nuts
    (8pcs)
    User Manual
    (1pc)
    Metal Bracket
    (1pc)
    B
    A
    N
    D
    S
    RC
    F
    U
    N
    C
    M
    E
    N
    U
    ENTER
    DISP
    VOL VOL
    50w x4
    USB
    Warranty Card
    (1pc)
    Facebook Card
    (1pc)
    THIS PACKAGE CONTAINS
    White
    Red
    Yellow
    Aux-In
    Left
    Right
    Black
    Grey
    Subwoofer
    Rear Line Out
    Front Line Out
    White
    White
    Red
    Red
    Left
    Left
    Right
    Right
    Antenna
    Fuse Box
    Left Rear Speaker (+) Green
    15A
    Left Rear Speaker (-) Green/Black
    Left Front Speaker (+) White
    Left Front Speaker (-) White/Black
    Right Front Speaker (+) Gray
    Right Front Speaker (-) Gray/Black
    Right Rear Speaker (+) Purple
    Right Rear Speaker (-) Purple/Black
    Accessory (+12V) Red
    Ground (-) Black
    Battery (+12V) Yellow
    Amp Remote (+12V) Blue
    1A
    CHARGING MAX
    Replace Fuse
    with AGU
    type only
    BATTERY
    20A
    Fuse and Fuse Holder
    (not included)
    Chassis
    ground
    point
    Battery Kill Switch
    (not included)
    OPTIONAL DIRECT BATTERY WIRING CIRCUIT
    BLACK
    Chassis
    ground
    point
    Ground wire
    Metal frame
    Recommended
    12 ~ 14ga
    Primary Wire
    (not included)
    15A
    INSERT
    USB
    YOUR
    USB CABLE
    YOUR
    ANTENNA
    To avoid potential shorts in the electrical
    system, be sure to disconnect the (–)
    battery cable before installation. Use this
    unit with a 12-Volt battery and negative
    grounding only. Failure to do so may result
    in a re or malfunction.
    When replacing the fuse, be sure to only use a
    fuse of the rating specied on this product. To
    avoid short-circuiting, cover any disconnected
    leads with insulating tape. It is specially impor-
    tant to insulate any unused wires, which if left uncovered may cause a
    short circuit. When connecting other devices to this product, refer to
    the manual for the product to be connected. The black cable is ground,
    make sure to connect the ground wire rst.
    Ensure that the ground cable is properly connected to metal parts of
    the vehicles body frame or direct to the battery if your vehicle does not
    have a grounded chassis frame. The ground cable of this units power
    amp and a second powered system must be connected to the frame
    separately with different screws. If the screw for the ground wire
    loosens or falls out, it could result in re or malfunction.
    CAUTION!!
    Do not ground or short the speaker leads
    1-805-751-4853
    www.bossaudio.com/support
    TECHNICAL SUPPORT
    This device complies with part 15 of the FCC Rules. Operation is
    subject to the following two conditions:
    (1) this device may not cause interference, and
    (2) this device must accept any interference, including interference
    that may cause undesired operation of this device.
    This transmitter must not be co-located or operated in conjunction
    with any other antenna or transmitter. The Bluetooth antenna cannot
    be removed (or replaced) by user. This equipment complies with
    FCC/ IC radiation exposure limits set forth for an uncontrolled
    environment and meets the FCC radio frequency (RF) Exposure
    Guidelines and RSS-102 of the IC radio frequency (RF) Exposure
    rules. This equipment has very low levels of RF energy that it
    deemed to comply without maximum permissive exposure
    evaluation (MPE). But it is desirable that it should be installed and
    operated keeping the radiator at least 20 cm or more away from
    person’s body (excluding extremities: hands, wrists, feet and
    ankles). Alteration or modications carried out without appropriate
    authorization may invalidate the user’s right to operate the
    equipment.
    NOTE: This equipment has been tested and found to comply with
    the limits for a Class B digital device, pursuant to Part 15 of the FCC
    Rules. These limits are designed to provide reasonable protection
    against harmful interference in a residential installation. This
    equipment generates, uses and can radiate radio frequency energy
    and, if not installed and used in accordance with the instructions,
    may cause harmful interference to radio communications. However,
    there is no guarantee that interference will not occur in a particular
    installation. If this equipment does cause harmful interference to
    radio or television reception, which can be determined by turning
    the equipment off and on, the user is encouraged to try to correct
    the interference by one or more of the following measures:
    Relocate or reorient the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from
    that to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.
    FCC COMPLIANCE STATEMENT
    1
    32
    TROUBLE CAUSE SOLUTION
    Unit will not turn on
    The fuse is blown Check / replace the fuse
    Ignition not engaged Turn ignition to on position
    No sound is heard
    Blown speaker Replace faulty speaker
    Volume is low / muted Press the volume level up
    Device is paused or muted
    Check your devices playing /
    volume status
    Cannot pair Bluetooth
    The Bluetooth function of the
    device is not enabled
    Refer to the user manual of the
    device for how to enable the
    Bluetooth function
    The MGR350B BT memory
    is full
    Follow how to reconnect a
    device in section D
    The audio quality is poor
    after connection with a
    Bluetooth enabled device The Bluetooth reception is poor
    Move the device closer to the
    audio system or remove any
    obstacle between the device
    and the systems antenna
    Sub woofer is not playing
    Sub level is muted
    Adjust sub level to preferred
    level
    Sub out is not enabled Follow steps in section H
    Unit has become
    unresponsive
    Power glitch or interference
    Disconnect power for
    10 seconds to reset
    Low battery power
    Charge battery, run the engine
    to recharge the battery
    Reset the main system Follow steps in section H
    INSTALLATION PRECAUTIONS
    Always consult with a professional installer
    Do not attempt to install or service this product by yourself.
    Installation or servicing of this product by persons without
    professional training and experience in electronic equipment and mo-
    torized vehicle accessories may be dangerous and could expose you
    to the risk of electric shock, injury or other hazards
    Refer any repairs to a qualied BOSS AUDIO SYSTEMS Service
    Center
    The MGR350B should be wired directly to a vehicles battery
    When wiring directly to the vehicles battery, be sure to disconnect
    the batteries negative terminal wire before starting any wiring pro-
    cedures, if extending the main power primary wire, it is suggested
    that an optional fuse and fuse holder (not included) with minimum
    rating of
    20 Amperes be in-line with the positive battery terminal
    The ground cable length should be as short as possible, if extend-
    ing from you battery, be sure to use a proper gauge rating for the
    length of the run, use only high quality copper primary type wire
    The MGR350B has a IPX6 weather resistant design, it should not be
    submerged in or under water under any circumstances
    Use only the installation parts provided with the MGR350B
    TOOLS NEEDED:
    - Measuring Tape / Ruler
    - Wrench and/or Pliers
    - Hole Saw
    - Crimp Tool
    CAUTION!!
    Using other mounting methods may void
    this warranty
    FM TUNER FREQUENCY RANGE
    USA 87.5~107.9MHz
    Europe 87.5~108MHz
    Asia 87.5~108MHz
    Australia 87.5~108MHz
    Usable Sensitivity: 12dB (S/N=30dB)
    Bands: 2
    AM TUNER FREQUENCY RANGE
    USA 530~1710KHz
    Europe 522~1620KHz
    Asia 522~1620KHz
    Australia 522~1620KHz
    Usable Sensitivity: 40dB (S/N=20dB)
    Bands: 1
    WEATHER BAND SELECTION
    CH.1 162.400MHz
    CH.2 162.425MHz
    CH.3 162.450MHz
    CH.4 162.475MHz
    CH.5 162.500MHz
    CH.6 162.525MHz
    CH.7 162.550MHz
    Bands: 1
    BLUETOOTH
    BT: 4.0
    BT Range: 33Ft / 10M (Class 2)
    BT Proles: A2DP / AVRCP 1.3
    USB DRIVE MEDIA SUPPORTED
    MP3
    WMA
    65,000 Songs
    32GB / FAT 32
    USB 2.0 High Speed
    USB Output Voltage: 5VDC @ 1A
    INTEGRATED AMPLIFIER
    MOSFET
    MAX Continuous Output: 240W
    (All channels driven)
    PEAK Power Rating: 63W / channel
    RMS Total Power Output: 150W
    Channels: 4
    Class: AB
    Frequency Response: 20-25kHz
    4Ω stable
    CHASSIS
    Chassis Dimensions HxDxW :
    0.79”x 3.75” x 3.5” / 20mm x 95mm x 90.2mm
    Button Backlight Illumination: RED LED
    FRONT/ REAR RCA Preamp Output: 2V
    RMS
    RCA Input Impedance: 10kΩ
    TFT: TN Type / Active Matrix
    GENERAL
    Power Source: 14.4VDC
    (10.8V ~ 16V allowable)
    Grounding System: Negative type
    Maximum Current Consumption: 15A
    3-way protection circuitry (thermal,
    o v e r l o a d , a n d s p e a k e r s h o r t p r o t e c t i o n )
    Unit Weight: 1.08lbs / 0.52kg
    Storage Temperature: 5
    o
    F to 113
    o
    F /
    -15
    o
    C to 45
    o
    C
    Operation Temperature: 14
    o
    F to 104
    o
    F /
    -10
    o
    C to 40
    o
    C
    Replacement Fuse: 15A
    (Replace with ATG Fuse Type Only)
    SPECIFICATIONS
    Specications subject to change without notice
    QUICK START GUIDE
    FOR CHARGING ONLY: Cell Phone and iPod
    Media Playback Not Supported
    iPod
    ®
    and iPhone
    ®
    are registered trademarks of Apple Inc.
    registered in the USA and other countries.
    BOSS Audio Systems is not afliated with Apple Inc.
    Copyright © 2015 AVA Enterprises Inc.
Boss MGR350B

Kell segítség?

Kérdések száma: 0

Van kérdése a (z) Boss MGR350B kapcsán, vagy segítségre van szüksége? Tegye fel a kérdését itt. Adjon világos és átfogó leírást a problémáról és a kérdéséről. Minél részletesebben ábrázolja a problémát és a kérdést, annál könnyebben tudnak más Boss MGR350B tulajdonosok megfelelő választ adni a kérdésére.

Itt ingyenesen megtekintheti a (z) Boss MGR350B kézikönyvét. Ez a kézikönyv a Rádiók kategóriába tartozik, és 1 ember értékelte, átlagosan 8.3. Ez a kézikönyv a következő nyelveken érhető el: Angol. Van kérdése a (z) Boss MGR350B kapcsán, vagy segítségre van szüksége? Itt tedd fel kérdéseidet

hasznalati-utasitasok.hu

Egy útmutatót keres? hasznalati-utasitasok.hu biztosítja, hogy rövid időn belül megtalálja az útmutatót.Az adatbázisunk több, mint 1 millió PDF útmutató tartalmaz, több, mint 10,000 márkától. Nap, mint nap újabb útmutatókat töltünk fel, így ön mindig megtalálhatja, amit keres.Nagyon egyszerű: csak írja be a márkanevet és a termék típusát a keresősávba és máris megtekintheti ingyenesen az ön által keresett útmutatót.

hasznalati-utasitasok.hu

© Szerzői jogok 2020 hasznalati-utasitasok.hu. Minden jog fenntartva.