Atdec TH-3070-CTW

Atdec TH-3070-CTW kézikönyv

(1)
  • G Attaching the Mount to the Ceiling Hanger
    M8x10mm
    Screw
    Swivel Insert
    Step 1
    Attach the three Swivel Inserts to the hanger in the height that
    you have chosen for the mounting of the display.
    Step 2
    Attach the front and rear Hanger Pole Collar so that it sits on
    the swivel collars as shown above. Tighten the M8x30mm
    screws so that the hanger pole collars is secure, however do
    not over tighten.
    Note: This operation will require two persons.
    Lift the display with brackets attached and hook the brackets over the
    sliders. Hold the display firmly and insert the two M8x45mm screws
    and tighten by using the Long 6mm Allen Key.
    Note: The brackets
    should rest on the
    horizontal bar with the
    slider between the
    bracket.
    I Mounting the Display
    Swivel Insert
    Collar Front
    Collar Rear
    H Attaching the Mount to the Ceiling Hanger
    Ceiling
    Mount
    Cables
    Step 1
    To use the in-built cable management, remove the Ceiling
    Mount Cover and feed the cables through the cable hole.
    Step 2
    Cut out enough space in the Ceiling Mount Cover to allow
    the cables to exit from, then push the Ceiling Mount Cover
    up, until in sits flush with ceiling.
    Ceiling Mount
    Cover
    Ceiling Mount
    Cover
    Cables
    Ceiling
    Mount
    Cut Out
    M8x30mm
    Screws
    No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
    Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 11.09.08 C
    J Adjusting the Viewing Position of your Display
    Step 1
    Loosen the two M8x45mm screws, and adjust the
    tilt angle of the display to the required position.
    Tighten the two locking screws with the Long
    6mm Allen Key provided.
    WARNING: Do not attempt to adjust tilt
    angle without firstly loosening locking
    screws.
    Doing so may damage the product.
    6mm Allen Key
    To adjust the pan position of the display, rotate the Hanger Pole
    Collar to the desired position. Once in position, tighten all 4
    M8x30mm screws as tight as possible to lock the display in
    position.
    Adjust grub screw 1 until the display sits level. Once the
    display is level, tighten grub screw 2 until it firmly tightens onto
    the horizontal bar. Tighten grub screw 3 firmly until it firmly
    tightens onto the horizontal bar and prevents it from moving.
    360° Rotation
    Tighten
    1
    2
    3
    -5° to 5°
    K Attaching the Adhesive Vinyl
    Adhesive
    Vinyl
    M8 Small
    Washer
    M8x45mm
    Screw
    Long 6mm
    Allen Key
    Tighten
    Loosen
    -5° to 25°
    Tilt
    Hanger
    Horizontal Bar
    1. Tilt Adjust
    Component Checklist
    M10 Steel
    Washer (x4)
    Nylon Plug
    (x4)
    M8 x55mm
    Screw
    M10 Coach
    Screw (x4)
    A Mounting the Ceiling Mount
    NOTE:
    The manufacturer
    does not accept
    responsibility for
    incorrect installation.
    The installer should
    satisfy himself that the
    ceiling is strong
    enough to support the
    Telehook Flat Panel
    Ceiling Mount unit of
    14kgs (31lbs) plus the
    maximum allowable
    monitor weight of
    91kgs (200lbs).
    Total of 105kgs
    (231lbs).
    Telehook Flat Panel
    Ceiling Mount
    supports a maximum
    weight of 91kgs
    (200lbs)
    TOOLS REQUIRED:
    z Power Drill
    z 12mm (1/2”) Drill Bit
    z 7mm (9/32”) Drill Bit
    z Adjustable wrench
    Ceiling Mount
    IMPORTANT:
    Ensure you have received all parts against the component checklist prior to installing.
    Bits Box
    12mm (1/2”)
    Hole
    Nylon Plug
    M10 Coach
    Screw
    Masonry
    Ceiling
    Masonry Mounting Option
    OR
    Timber Beam Mounting Option
    Timber
    Beam
    M10 Coach
    Screw
    7mm (9/32”)
    Hole
    Inner Hanger
    M8 x10mm
    Screw (x24)
    M6 x12mm
    Grub Screw
    (x3)
    M10 Washer
    M10 Washer
    Collar Front
    Collar Rear
    Swivel Insert
    (x3)
    Adhesive Vinyl
    Strip (x6)
    M8x30mm
    Screw (x4)
    NOTE: Ensure all four M10 Coach Screws are used when mounting the Ceiling Mount.
    Note: The Vinyl Strips may need to be cut to length
    depending on the hanger configuration chosen.
    The Telehook Flat Panel Ceiling Mount’s
    set up is now complete. The remaining
    unused holes can be covered using the
    6 white adhesive vinyl strips for improved
    aesthetics. Peel the backing from the
    strip and apply the adhesive side onto
    the hanger(s) so that they cover the
    unused holes.
    Padlock
    (not supplied)
    5mm (
    3
    /
    16
    ”)
    diameter shackle
    For added security you may
    choose to attach a padlock to
    one or both brackets to prevent
    the theft of the display. It is
    recommended that the padlock
    should have a shackle diameter
    of 5mm (
    3
    /
    16
    ”).
    L Security Option
    2. Pan Adjust
    3. Horizontal Adjust
    Wall Mount Horizontal Bar
    Slider (x2)
    Hanger Joiner
    Extension Hanger
    Collar Joiner
    TM
    Installation Instructions
    Flat Panel Ceiling Mount
    M8 x45mm
    Locking Screws
    (x2)
    Multi
    Washer (x6)
    M5 x16mm
    Mounting
    Screws (x6)
    M6 x16mm
    Mounting
    Screws (x6)
    M8 x16mm
    Mounting
    Screws (x6)
    M4 x16mm
    Mounting
    Screws (x6)
    Long 6mm
    Allen Key
    M8 Small
    Washer
    (x2)
    3mm
    Allen Key
    5mm
    Allen Key
    M8 Small
    Washer
    M8x45mm
    Screw
    Long 6mm
    Allen Key
    Tighten
    6mm Allen
    Key
    TH-3070- CTW
    Ceiling Mount Cover
    Wall Mount Bracket (Left)
    Wall Mount Bracket (Right)
    Clinch Nuts
Atdec TH-3070-CTW

Kell segítség?

Kérdések száma: 0

Van kérdése a (z) Atdec TH-3070-CTW kapcsán, vagy segítségre van szüksége? Tegye fel a kérdését itt. Adjon világos és átfogó leírást a problémáról és a kérdéséről. Minél részletesebben ábrázolja a problémát és a kérdést, annál könnyebben tudnak más Atdec TH-3070-CTW tulajdonosok megfelelő választ adni a kérdésére.

Itt ingyenesen megtekintheti a (z) Atdec TH-3070-CTW kézikönyvét. Ez a kézikönyv a TV fali konzolok kategóriába tartozik, és 1 ember értékelte, átlagosan 8.4. Ez a kézikönyv a következő nyelveken érhető el: Angol. Van kérdése a (z) Atdec TH-3070-CTW kapcsán, vagy segítségre van szüksége? Itt tedd fel kérdéseidet

Atdec TH-3070-CTW specifikációk

Általános
Márka Atdec
Modell TH-3070-CTW
Termék TV fali konzol
EAN 411378260437, 763615998390, 881493004627
Nyelv Angol
Fájltípus PDF
Kialakítás
Termék színe Fehér
További jellemzők
Elfordulás 360°
Képernyőméret-kompatibilitás 30 - 65 "
Tömeg (imperial) 200 font
Súly (max.) 91 kg
5 years
Rögzítőegység VESA & nonVESA 180mm x 685mm / 100mm x 430mm
Ergonómia
Elfordulási szög 5 °
Billenési szög tartománya -5 - 25 °
Maximális távolság a plafonig 2000 mm
Tömeg és méretek
Tömeg 14000 g
Tartókonzol
Felszerelés típusa Fali